CAS Number 7647-01-0, Hydrochloric Acid, HCl USP NF BP Ph Eur FCC Food Analytical Reagent Grade Manufacturers Exporters
------ 
CAS Number 7647-01-0, Hydrochloric Acid, HCl USP NF BP Ph Eur FCC Food Analytical Reagent Grade Manufacturer Exporter
For Properties Specifications of Hydrochloric Acid, HCl Click Properties, Specifications of Hydrochloric Acid, HCl Manufacturer.
For Uses of Hydrochloric Acid, HCl Click Uses of Hydrochloric Acid, HCl Manufacturer.
For For SDS MSDS Sheet of Hydrochloric Acid, HCl Click SDS Safety Data Sheet MSDS Sheet of Hydrochloric Acid, HCl Manufacturer.
The Properties and Specifications of Hydrochloric Acid, HCl:
Dilute Hydrochloric Acid BP Ph Eur Grade:
Ph. Eur.
DEFINITION
Content: 9.5 per cent m/m to 10.5 per cent m/m of HCl.
PREPARATION
To 726 g of water add 274 g of concentrated hydrochloric acid and mix.
IDENTIFICATION
A. It is strongly acid.
B. It gives the reactions of chlorides.
C. It complies with the limits of the assay.
TESTS
Appearance: It is clear and colourless.
Free chlorine: Maximum 1 ppm.
Sulfates: Maximum 5 ppm.
Residue on evaporation: Maximum 0.01 per cent.
Hydrochloric Acid USP NF Grade:
HCl --- 36.46 --- CAS 7647-01-0.
Hydrochloric Acid contains not less than 36.5 percent and not more than 38.0 percent, by weight, of HCl.
Identification: It responds to the tests for Chloride.
Residue on ignition: To 20 mL add 2 drops of sulfuric acid, evaporate to dryness, and ignite: not more than 2 mg of residue remains (about 0.008%).
Bromide or iodide, Free bromine or chlorine, Sulfate, and Sulfite: To pass the tests.
Heavy metals: Evaporate 3.4 mL (4 g) on a steam bath to dryness, add 2 mL of 1 N acetic acid to the residue, then dilute with water to 25 mL: the limit is 5 ppm.
Hydrochloric Acid FCC Food Grade:
HCl --- Formula wt 36.46
INS: 507 CAS 7647-01-0
DESCRIPTION
Hydrochloric Acid occurs as a clear, colorless or slightly yellow, corrosive liquid. It is a water solution of hydrogen chloride of varied concentrations. It is miscible with water and with alcohol. Concentrations of Hydrochloric Acid are expressed in percent by weight or may be expressed in degrees Baume´ from which percents of Hydrochloric Acid and specific gravities may readily be derived. Concentrated Hydrochloric Acid fume in moist air, lose hydrogen chloride, and create a corrosive atmosphere. Because of these characteristics, observe suitable precautions during sampling and analysis to prevent losses.
Function: Acidifier.
REQUIREMENTS
Labeling: Indicate the content, by weight, of Hydrochloric Acid (HCl). Alternatively, indicate the range of Hydrochloric Acid content, the range of degrees Baume and/or the specific gravity range.
Identification: A sample gives positive tests for Chloride.
Assay: Not less than 97.0% and not more than 103.0% of the labeled amount of HCl, or within the range specified on the label.
Color: Passes test.
Iron: Not more than 5 mg/kg.
Lead: Not more than 1 mg/kg.
Nonvolatile Residue: Not more than 0.5%.
Organic Compounds: Total Organic Compounds (Non-Fluorine-Containing) -Not more than 5 mg/kg, including Benzene Not more than 0.05 mg/kg. and Fluorinated Organic Compounds (total) Not more than 0.0025%.
Oxidizing Substances (as Cl2): Not more than 0.003%.
Reducing Substances (as SO3): Not more than 0.007%.
Specific Gravity: Within the range specified or implied by the vendor.
Sulfate: Not more than 0.5%.
Hydrochloric Acid Analytical Reagent Grade:
HCl --- Formula Wt 36.46 --- CAS Number 7647-01-0
REQUIREMENTS
Appearance: Passes test
Assay: 36.5-38.0% HCl
MAXIMUM ALLOWABLE
Color (APHA): 10
Residue after ignition: 5 ppm
Bromide (Br): 0.005%
Sulfate (SO4): 1 ppm
Sulfite (SO3): 1 ppm
Extractable organic substances: Passes test (about 5 ppm)
Free chlorine (Cl): 1 ppm
Ammonium (NH4): 3 ppm
Arsenic (As): 0.01 ppm
Heavy metals (as Pb): 1 ppm
Iron (Fe): 0.2 ppm.
Hydrochloric Acid, Ultratrace Analytical Reagent Grade:
(suitable for use in ultratrace elemental analysis)
HCl --- Formula Wt 36.46 --- CAS Number 7647-01-0
NOTE. Reagent must be packaged in a preleached teflon bottle and used in a clean environment to maintain purity
REQUIREMENTS
Appearance: Clear
Assay: 20-38%
MAXIMUM ALLOWABLE
Sulfate: 1 ppm
Aluminum (Al): 1 ppb
Barium (Ba): 1 ppb
Boron (B): 5 ppb
Cadmium (Cd): 1 ppb
Calcium (Ca): 1 ppb
Chromium (Cr): 1 ppb
Cobalt (Co): 1 ppb
Copper (Cu): 1 ppb
Iron (Fe): 5 ppb
Lead (Pb): 1 ppb
Lithium (Li): 1 ppb
Magnesium (Mg): 1 ppb
Manganese (Mn): 1 ppb
Molybdenum (Mo): 1 ppb
Mercury (Hg): 1 ppb
Potassium (K): 1 ppb
Selenium (Se): 10 ppb
Silicon (Si): 5 ppb
Sodium (Na): 5 ppb
Strontium (Sr): 1 ppb
Tin (Sn): 1 ppb
Titanium (Ti): 1 ppb
Vanadium (V): 1 ppb
Zinc (Zn): 1 ppb
Zirconium (Zr): 1 ppb.
The Uses of Hydrochloric Acid, HCl:
Hydrochloric acid is a strong inorganic acid that is utilized in research and other fine uses. It has use in almost all types of industries.
The MSDS-SDS Hazard Statement of Hydrochloric Acid, HCl:
Hydrochloric Acid SDS, Safety Data Sheet
MSDS Sheet, Material Safety Data Sheet 11-Dec-24
Section 1: Product Identification
Product Name & Other Names: Hydrochloric Acid or Muriatic Acid.
CAS No.: 7647-01-0
EINECS EC Number: 231-595-7
Relevant identified uses and uses advised against if any: Laboratory chemicals, Manufacture of substances. For Industrial use.
Suppliers: As per letter head.
Section 2: Hazard Identification
GHS, Globally Harmonized System Classification in accordance with 29 CFR 1910
Classification according to Regulation (EC) No 1272/2008
Corrosive to Metals Category 1 H290
Skin corrosion/irritation Category 1A, B, C H314
Specific target organ toxicity - single exposure Category 3, Respiratory system, H335
Labeling according Regulation (EC) No 1272/2008
GHS Label Elements  Corrosive |
Signal Words: Danger
Hazard statements:
H290: May be corrosive to metals.
H314: Causes severe skin burns and eye damage.
H335: May cause respiratory irritation.
Precautionary statements:
P234: Keep only in original container.
P260: Do not breathe dust/fume/gas/mist/vapors/spray.
P280: Wear protective gloves/protective clothing/eye protection/face protection.
P303+361+353: IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower.
P304+P340+P310: IF INHALED: Remove person to fresh air and keep comfortable for breathing. Immediately call a POISON CENTER/doctor.
P305+351+338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do – continue rinsing.
Section 3: Composition / Information on Ingredients
Product Name & Other Names: Hydrochloric Acid or Muriatic Acid.
CAS No.: 7647-01-0
EINECS EC Number: 231-595-7
Percentage: Less than 40% in water.
Section 4: First Aid Measures
Always seek medical attention after first aid measures are provided.
Eye Contact: Check for and remove any contact lenses. In case of contact, immediately flush eye with plenty of water for at least 15 minutes. Get medical attention immediately.
Skin Contact: Immediately flush skin with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Call a physician, immediately.
Ingestion: If swallowed, do not induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to and unconscious person. Loosen tight clothing such as a collar, tie, belt, or waistband. Get medical attention immediately.
Inhaled: If breathed in, move person into fresh air. If not breathing, give artificial respiration. Consult a physician.
Medical Conditions generally Aggravated by Exposure: Repeated exposure of the eyes can produce eye irritation. Inhalation can produce respiratory irritation or sensitization.
Section 5: Fire Fighting Measures
Flash Point: NA
Fire Extinguishing Media: Adapt extinguishing media to the environment. Use water spray, alcohol-resistant foam, dry chemical or carbon dioxide.
Special Fire Fighting Procedures: Wear self contained breathing apparatus for firefighting if necessary.
Unusual Fire and Explosion Hazards: Flammable hydrogen gas may be produced on prolong contact with metals such as aluminum, tin lead and zinc.
Hazardous combustion products: Hydrogen chloride and toxic fumes.
Special Information: In the event of a fire, wear full protective clothing and NIOSH-approved self-contained breathing apparatus with full face piece operated in the pressure demand or other positive pressure mode.
Section 6: Accidental Release Measures
Personal precautions, protective equipment, and emergency procedures: Avoid breathing dust/fumes/gas/mist/vapors/spray. Use individual protective equipment (waterproof boots, suitable protective clothing, safety glasses, etc.).
Environmental precautions: Do not let the product enter drains, soil, or water sources.
Methods and materials used for containment Cleanup procedures and Storage: Do not inhale dust, vapors, mist, or gas. Avoid dust formation. Contain spilled material. Cover with an inert, non-combustible absorbent material, (e.g. sand, earth, diatomaceous earth, vermiculite). Use a shovel to put the material into a convenient waste disposal container.
Section 7: Handling and Storage
Precautions for safe handling: Apply according to good manufacturing and industrial hygiene practices. Ensure proper ventilation. In case of insufficient ventilation, wear suitable respiratory equipment. Wash thoroughly after handling. Do not drink, eat, or smoke while handling. Avoid contact with skin, eyes, and clothing. Minimize dust generation. Avoid breathing dust/fumes/gas/mist/vapors/spray. Keep container tightly closed. Avoid ingestion and inhalation. Use individual protective equipment (waterproof boots, suitable protective clothing, safety glasses, etc.).
Conditions for safe storage, including any incompatibilities: Store in cool, dry, and ventilated area away from heat sources and protected from sunlight in tightly closed original container. Keep air contact to a minimum. Store protected from heat, sparks and ignition sources and incompatible materials. Avoid inhalation of dust/mist/vapor. Do not store with incompatible materials like strong oxidizing agents, strong bases, ammonia, ozone, fluorine, powdered metals, amines, potassium permanganate, salts of oxyhalogenic acids, semi metallic oxides, semi metallic hydrogen compounds, aldehydes, vinyl methyl ether.
Section 8: Exposure Controls / Personal Protection
Components with workplace control parameters
USA ACGIH TLV: 2 ppm
USA OSHA PEL: 5 ppm Ceiling.
Engineering Controls Ventilation required: It should be handled or transferred in an approved fume hood or with adequate ventilation.
Ventilation System: A system of local and/or general exhaust is recommended to keep employee exposures as low as possible.
Personal Respirators (NIOSH Approved): For conditions of use where exposure to dust or mist is apparent and engineering controls are not feasible, a particulate respirator may be worn.
Skin Protection: Wear protective gloves and clean body-covering clothing.
Eye Protection: Use chemical safety goggles and/or full face shield where dusting or splashing of solutions is possible. Maintain eye wash fountain and quick-drench facilities in work area.
Other Control Measures: Maintain good housekeeping in work area. Handle in accordance with good industrial hygiene and safety practice. Wash hands after handling.
Section 9 Physical and Chemical Properties
Appearance and Physical State: Colorless to faint yellow liquid.
Odor (threshold): Pungent.
Odor threshold: No data found.
pH: Highly acidic.
Relative density: Varies with percentage.
Melting Point: Varies with percentage.
Boiling Point: Varies with percentage.
Flash point: No data found.
Auto-ignition temperature: No data found.
Decomposition temperature: No data found.
Upper/lower flammability or explosive limits: No data found.
Vapor pressure: No data found.
Vapor density: No data found.
Evaporation rate: No data found.
Flammability (solid, gas): No data found.
Partition coefficient: n-octanol/water: No data found.
Solubility in Water: Soluble in water.
Viscosity: No data found.
Section 10: Stability and Reactivity
Stability: It is stable under ordinary conditions of use and storage.
Reactivity: Reacts with metals to release hydrogen.
Materials to Avoid (Incompatibility): Strong oxidizing agents, Strong bases, Ammonia, Ozone, Fluorine, Powdered metals, Amines, Potassium permanganate, Salts of oxyhalogenic acids, Semi metallic oxides, Semi metallic hydrogen compounds, Aldehydes, Vinyl methyl ether. Heat sensitive.
Hazardous Decomposition Products: Thermal decomposition may produce hydrogen chloride and toxic fumes.
Hazardous Polymerization: Will not occur.
Section 11: Toxicological Information
Results of component toxicity test:
LD50 oral rat 700 mg/kg
LD50 dermal rabbit 5010 mg/kg
Carcinogenicity: This product is not classifiable as to its carcinogenicity based on its IARC, ACGIH, NTP, or EPA classification.
Mutagenic Effects: No data found.
Reproductive Effects: No data found.
Developmental Effects: No data found.
Teratogenicity: No data found.
Section 12: Ecological Information
Toxicity to fish: Toxicity to fishLC50 Leuciscus idus (Golden orfe): 862 mg/l (1 N solution). EC50 Daphnia 1 < 56 mg/l (EC50; 72 h)
The product may affect the acidity (pH-factor) in water with risk of harmful effects to aquatic organisms.
Bioaccumulation/ Accumulation: No data found.
Mobility: Will likely be mobile in the environment due to its water solubility.
Results of PBT and vPvB assessment: No data found.
Section 13 Disposal Considerations
State and local laws governing disposal of materials can differ. Ensure proper disposal compliance with proper authorities before disposal. Follow all the pollution control rules.
Section 14: Transportation Information
DOT USA, TDG Canada & ADR/RID Europe:
Proper shipping name: Hydrochloric acid
Hazard Class: 8; Packaging group: II
UN Number: UN1789
IATA:
Proper shipping name: Hydrochloric acid
Hazard Class: 8; Packaging group: II
UN Number: UN1789
IMO:
Proper shipping name: Hydrochloric acid
Hazard Class: 8; Packaging group: II
UN Number: UN1789
Section 15: Regulatory Information
USA:
California Proposition 65: Not listed.
Section 16: Other Information
Disclaimer:
**************************
Our company provides this MSDS sheet in good faith but makes no representation as to its comprehensiveness or accuracy. This SDS sheet is intended only as a guide to the appropriate precautionary handling of the material by a properly trained person using this product. The above information has been compiled from various sources and has the possibility of discrepancy and being out-dated information. Individuals receiving the information must exercise their independent judgment and do further search in determining its appropriateness for a particular purpose. In no case shall our company be liable to loss or damages by the product user.
**************************
Anmol Chemicals & Pharmaceuticals Pvt. Ltd. is an off-shoot of Anmol Chemicals Taloja. It is located in MIDC Taloja and it is manufacturing pharmaceutical grades of API, Excepients, Food grade and Reagent grade chemicals. Anmol Chemicals & Pharmaceuticals Pvt. Ltd. is a several decades old group of companies, engaged in manufacturing, supplying, distributing, wholesale supplies for actual users, retail or small pack supplies for research and development chemicals, fine and speciality chemicals, pharmaceutical excipients, mineral fortifiers in chemically pure, Analytical reagent grade, IP BP USP Ph Eur EP JP and other pharmaceutical grade monograph including FCC Food grade chemicals and Nutraceuticals, Mineral Fortifiers at best prices.
Hydrochloric Acid, HCl Structure
CAS Number 7647-01-0, Hydrochloric Acid, HCl Manufacturer Exporter
ANMOL CHEMICALS & PHARMACEUTICALS Pvt. Ltd.
India, USA, Europe, UAE
TELEPHONE: +912223770100
Navi Mumbai, INDIA
e-mail: info(At the rate i.e. @)anmol.org
Copyright. 11-dec-24
We manufacture:
Esmolol Hydrochloride or Esmolol HCl
Fexofenadine HCl or Fexofenadine Hydrochloride
Fingolimod Hydrochloride or Fingolimod HCl
Nebivolol Hydrochloride or Nebivolol HCl
Paroxetine HCl or Paroxetine Hydrochloride
Phenazopyridine Hydrochloride or Phenazopyridine HCl
Pioglitazone Hydrochloride or Pioglitazone HCl