CAS Number 12042-91-0 and 1327-41-9, Aluminium Chlorohydrate or Aluminum Chlorohydrate Solution Powder Dihydrate Anhydrous USP Grade Manufacturers Exporters
------ 
Aluminum Chlorohydrate Powder and Aluminum Chlorohydrate Solution
CAS Number Dihydrate 12042-91-0 Aluminum Chlorohydrate Dihydrate Manufacturer Exporter
CAS Number Dihydrate 1327-41-9 Aluminum Chlorohydrate Anhydrous Manufacturer Exporter
For Properties Specifications of Aluminum Chlorohydrate Solution Powder Dihydrate Anhydrous Click Properties, Specifications of Aluminum Chlorohydrate Solution Powder Dihydrate Anhydrous Manufacturer.
For Uses of Aluminum Chlorohydrate Solution Powder Dihydrate Anhydrous Click Uses of Aluminum Chlorohydrate Solution Powder Dihydrate Anhydrous Manufacturer.
For For SDS MSDS Sheet of Aluminum Chlorohydrate Solution Powder Dihydrate Anhydrous Click SDS Safety Data Sheet MSDS Sheet of Aluminum Chlorohydrate Solution Powder Dihydrate Anhydrous Manufacturer.
The Properties and Specifications of Aluminum Chlorohydrate Solution Powder Dihydrate Anhydrous :
Aluminium chlorohydrate is an aluminium salts having the general formula AlnClAlnCl(3n-m)(OH)m. It is used in cosmetics as an antiperspirant and as a coagulant in water purification. In water purification, this compound is used because of its high charge, which makes it more effective at destabilizing and removing suspended materials than other aluminium salts.
Specifications of Aluminum Chlorohydrate Solution USP Grade:
Aluminum Chlorohydrate Solution consists of complex basic aluminum chloride that is polymeric and encompasses a range of aluminum-to-chloride ratios between 1.91:1 and 2.10:1. The following solvents may be used: water, propylene glycol, dipropylene glycol, or alcohol. It contains the equivalent of not less than 90.0 percent and not more than 110.0 percent of the labeled concentration of anhydrous aluminum chlorohydrate.
Packaging and storage: Preserve in well-closed containers.
Labeling: Label Solution to state the solvent used and the claimed concentration of anhydrous aluminum chlorohydrate contained therein.
Identification:
A: A solution containing the equivalent of about 100 mg of anhydrous aluminum chlorohydrate per mL responds to the tests for Aluminum and for Chloride.
B: Identification of propylene glycol (where stated on the label): Add about 10 mL of isopropyl alcohol to 2 g of Solution, mix, and filter. Evaporate the filtrate to about 1 mL on a steam bath: the IR spectrum of a film of this solution on a silver chloride disk exhibits maxima only at the same wavelengths as that of a similar preparation of a film of propylene glycol.
C: Identification of dipropylene glycol (where stated on the label): Add about 10 mL of isopropyl alcohol to 2 g of Solution, mix, and filter. Evaporate the filtrate to about 1 mL on a steam bath: the IR spectrum of a film of this solution on a silver chloride disk exhibits maxima only at the same wavelengths as that of a similar preparation of a film of dipropylene glycol.
D: Identification of alcohol (where stated on the label): In a small beaker mix 5 drops of Solution with 1 mL of potassium permanganate solution (1 in 100) and 5 drops of 2 N sulfuric acid. Immediately cover the beaker with filter paper moistened with a freshly prepared solution of 0.1 g of sodium nitroferricyanide and 0.25 g of piperazine in 5 mL of water: an intense blue color is produced on the filter paper, the color fading after a few minutes.
pH: between 3.0 and 5.0, in a solution prepared by diluting 3 g of the solution with water to obtain 10 mL.
Arsenic: Prepare the Test Preparation using an accurately weighed quantity of the Solution. The limit is 2 ppm.
Heavy metals: Prepare the Test Preparation using an accurately weighed quantity of the Solution. The limit is 0.001%.
Limit of iron: To pass the test --- (75 micro-gm per g).
Content of aluminum: To pass the test.
Content of chloride: To pass the test.
Aluminum/chloride atomic ratio: --- the ratio is between 1.91:1 and 2.10:1.
Specifications of Aluminum Chlorohydrate USP Grade:
Aly(OH)3y-zClz·H2O
Aluminum chlorohydroxide.
Aluminum hydroxychloride.
Dihydrate --- 12042-91-0.
Anhydrous --- 1327-41-9.
Aluminum chlorohydroxide, dihydrate.
Aluminum hydroxychloride, dihydrate.
Dihydrate --- 210.48 --- CAS 12042-91-0.
Anhydrous --- 174.45 --- CAS 1327-41-9.
Aluminum Chlorohydrate consists of complex basic aluminum chloride that is polymeric and loosely hydrated and encompasses a range of aluminum to chloride atomic ratios between 1.91:1 and 2.10:1. It contains the equivalent of not less than 90.0 percent and not more than 110.0 percent of the labeled amount of anhydrous aluminum chlorohydrate.
Identification: A solution (1 in 10) responds to the tests for Aluminum and for Chloride.
pH: between 3.0 and 5.0, in a solution [15 in 100 (w/w)].
Arsenic: 2 micro-gm per g.
Heavy metals: 0.002%.
Limit of iron: To pass the test --- (150 micro-gm per g).
Content of aluminum: To pass the test.
Content of chloride: To pass the test.
Aluminum/chloride atomic ratio: ---: the ratio is between 1.91:1 and 2.10:1.
The Uses of Aluminum Chlorohydrate Solution Powder Dihydrate Anhydrous :
It is used in cosmetics as an antiperspirant and as a coagulant in water purification. In water purification, this compound is used because of its high charge, which makes it more effective at destabilizing and removing suspended materials than other aluminium salts.
The MSDS-SDS Hazard Statement of Aluminum Chlorohydrate Solution Powder Dihydrate Anhydrous :
Aluminum Chlorohydrate Solution or Aluminium Chlorohydrate Solution or Poly Aluminum Chloride SDS Safety Data Sheet
MSDS Sheet, Material Safety Data Sheet 31-Dec-22
1. Product Identification
Product Name & Other Names: Aluminum Chlorohydrate Solution or Aluminium Chlorohydrate Solution or Poly Aluminum Chloride.
CAS No.: 1327-41-9
EINECS: EC Number: 215-477-2
Molecular Weight: Varies
Chemical Formula: AlnCl(3n-m)(OH)m in water.
Relevant uses and uses advised against (if any): Industrial Manufacturing.
2. Hazards Identification
GHS, Globally Harmonized System Classification in accordance with 29 CFR 1910
Classification according to Regulation (EC) No 1272/2008:
Acute toxicity, Oral (Category 5)
Skin corrosion/irritation (Category 2)
Serious eye damage/eye irritation (Category 2A)
Labeling according to GHS & Regulation (EC) No 1272/2008
GHS Label Elements  Irritant |
Signal Words: Warning
Hazard statements:
H303: May be harmful if swallowed.
H315: Causes skin irritation.
H319: Causes serious eye irritation.
Precautionary statements:
P261: Avoid breathing dust/ fume/ gas/ mist/ vapors/ spray.
P262: Do not get in eyes, on skin, or on clothing.
P264 Wash skin thoroughly after handling.
P280: Wear protective gloves/protective clothing/eye protection/face protection.
P301+P330 + P331 IF SWALLOWED: rinse mouth. Do NOT induce vomiting.
P302+P352 IF ON SKIN: Wash with plenty of soap and water.
P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P332+313: If skin irritation occurs: Get medical advice/attention.
P337+P313: If eye irritation persists: Get medical advice/ attention.
3. Composition/Information on Ingredients
Product Name & Other Names: Aluminum Chlorohydrate Solution or Aluminium Chlorohydrate Solution or Poly Aluminum Chloride.
CAS No.: 1327-41-9
EINECS: EC Number: 215-477-2
Percent: 40-60% in water.
4. First Aid Measures
Always seek medical attention after first aid measures are provided.
Inhalation: Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical attention.
Ingestion: Never give anything by mouth to an unconscious person. Get medical attention.
Skin Contact: Wipe off excess material from skin then immediately flush skin with plenty of water for at least 15 minutes. Remove contaminated clothing and shoes. Get medical attention. Wash clothing before reuse. Thoroughly clean shoes before reuse.
Eye Contact: Immediately flush eyes with plenty of water for at least 15 minutes, lifting lower and upper eyelids occasionally. Get medical attention immediately.
Note to Physician: Treat symptomatically.
5. Fire Fighting Measures
Flammability of the Product: The product is not flammable.
Products of Combustion: It forms oxides of aluminum and hydrochloric acid when heated to decomposition.
Fire Extinguishing Media: Use water spray, dry chemical, foam, or carbon dioxide.
Special Information In the event of a fire, wear full protective clothing and NIOSH-approved self-contained breathing apparatus with full face piece operated in the pressure demand or other positive pressure mode. At high temperatures or when moistened under fire conditions, it may produce toxic or irritating fumes.
6. Accidental Release Measures
Personal precautions, protective equipment, and emergency procedures: Avoid breathing dust/fumes/gas/mist/vapors/spray. Use individual protective equipment (waterproof boots, suitable protective clothing, safety glasses, etc.). Do not approach facing the wind.
Environmental precautions: Do not let the product enter drains, soil, or water sources.
Methods and materials used for containment Cleanup procedures and Storage: Contain spilled material. Do not let the product enter drains. Use a shovel to put the material into a convenient waste disposal container. Finish cleaning by spreading water and swab.
7. Handling and Storage
Precautions for safe handling: Apply according to good manufacturing and industrial hygiene practices. Ensure proper ventilation. In case of insufficient ventilation, wear suitable respiratory equipment. Wash thoroughly after handling. Do not drink, eat, or smoke while handling. Avoid contact with skin, eyes, and clothing. Minimize dust generation. Avoid breathing dust/fumes/gas/mist/vapors/spray. Keep container tightly closed. Avoid ingestion and inhalation. Use individual protective equipment (waterproof boots, suitable protective clothing, safety glasses, etc.).
Conditions for safe storage, including any incompatibilities: Store in cool, dry, and ventilated area away from heat sources and protected from sunlight in tightly closed original container. Keep air contact to a minimum. Do not leave the material container open. Store protected from heat, sparks and ignition sources and incompatible materials. Avoid inhalation of dust/mist/vapor. Do not store with incompatible materials like oxidizing material, acids, alkalis, and combustible substances. It is to be stored in corrosive area.
8. Exposure Controls/Personal Protection
Airborne Exposure Limits: None established. Assure it as below 2mg/m3.
Ventilation System: A system of local and/or general exhaust is recommended to keep employee exposures as low as possible.
Personal Respirators (NIOSH Approved): For conditions of use where exposure to dust or mist is apparent and engineering controls are not feasible, a particulate respirator may be worn.
Skin Protection: Wear protective gloves and clean body-covering clothing.
Eye Protection: Use chemical safety goggles and/or full face shield where dusting or splashing of solutions is possible. Maintain eye wash fountain and quick-drench facilities in work area.
Other Control Measures: Maintain good housekeeping in work area. Handle in accordance with good industrial hygiene and safety practice.
9. Physical and Chemical Properties
Appearance: Clear to yellowish liquid.
Odor: None
Odor threshold: Not available.
pH: 3 to 5.
Relative density: 1.3 to 1.4
Melting Point: -4C to -8C
Initial boiling point and boiling range: Not available.
Flash point: Not available.
Auto-ignition temperature: Not available.
Decomposition temperature: Not available.
Upper/lower flammability or explosive limits: Not available.
Vapor pressure: Not available.
Vapor density: Not available.
Evaporation rate: Not available.
Flammability (solid, gas): Not available.
Partition coefficient: n-octanol/water: Not available.
Solubility: Readily soluble in water.
Viscosity: Not available.
10. Stability and Reactivity
Stability: Stable under ordinary conditions of use and storage. It must be kept in airtight containers.
Hazardous Decomposition Products: It produces oxides of aluminum along with hydrochloric acid when heated to decomposition.
Hazardous Polymerization: Will not occur.
Incompatibilities: Incompatible with oxidizing material acids and alkalis.
Conditions to Avoid: Heat, Sun light, Incompatibles, Metals.
11. Toxicological Information
Toxicity to Animals: Oral, rat: LD50 = 9187 mg/kg.
Carcinogenic Effects: Not a reported carcinogen.
Mutagenic Effects: Not available.
Teratogenic Effects: Not available.
Developmental Toxicity: Not available.
12. Ecological Information
Environmental Toxicity: Toxicity to fish: LC50 - fish - Not available
Persistence and Degradability: No information available.
Mobility: No information available.
Bioaccumulation/ Accumulation: No information available.
Results of PBT and vPvB assessment: No data available for assessment.
Avoid draining the material in waterways.
13. Disposal Considerations
Whatever cannot be saved for recovery or recycling should be managed in an appropriate and approved waste disposal facility. Processing use or contamination of this product may change the waste management options.
14. Transport Information
DOT (USA) & ADR/RID Europe: Not Regulated.
IMDG: Not Regulated.
IATA: Not Regulated.
15. Regulatory Information
USA:
SARA 311/312 Hazards: Immediate Health Hazard. See section 2.
California Prop 65: This product does not contain any chemicals known to State of California to cause cancer, birth defects, or any other reproductive harm.
16. Other Information
Disclaimer:
**************************
Our company provides this MSDS sheet in good faith but makes no representation as to its comprehensiveness or accuracy. This SDS sheet is intended only as a guide to the appropriate precautionary handling of the material by a properly trained person using this product. The above information has been compiled from various sources and has the possibility of discrepancy and being out-dated information. Individuals receiving the information must exercise their independent judgment and do further search in determining its appropriateness for a particular purpose. In no case shall our company be liable to loss or damages by the product user.
**************************
Aluminum Chlorohydrate Powder or Aluminium Chlorohydrate Powder or Poly Aluminium Chloride SDS, Safety Data Sheet
MSDS Sheet, Material Safety Data Sheet 31-Dec-22
1. Product Identification
Product Name & Other Names: Aluminum Chlorohydrate Powder or Aluminium Chlorohydrate Powder or Poly Aluminium Chloride.
CAS No.: 1327-41-9
EINECS: EC Number: 215-477-2
Molecular Weight: Varies
Chemical Formula: AlnCl(3n-m)(OH)m
Relevant uses and uses advised against (if any): Industrial Manufacturing.
2. Hazards Identification
GHS, Globally Harmonized System Classification in accordance with 29 CFR 1910
Classification according to Regulation (EC) No 1272/2008:
Acute toxicity, Oral (Category 5)
Skin corrosion/irritation (Category 2)
Serious eye damage/eye irritation (Category 2A)
Labeling according to GHS & Regulation (EC) No 1272/2008
GHS Label Elements Irritant |
Signal Words: Warning
Hazard statements:
H303: May be harmful if swallowed.
H315: Causes skin irritation.
H319: Causes serious eye irritation.
Precautionary statements:
P261: Avoid breathing dust/ fume/ gas/ mist/ vapors/ spray.
P262: Do not get in eyes, on skin, or on clothing.
P264 Wash skin thoroughly after handling.
P280: Wear protective gloves/protective clothing/eye protection/face protection.
P301+P330 + P331 IF SWALLOWED: rinse mouth. Do NOT induce vomiting.
P302+P352 IF ON SKIN: Wash with plenty of soap and water.
P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P332+313: If skin irritation occurs: Get medical advice/attention.
P337+P313: If eye irritation persists: Get medical advice/ attention.
3. Composition/Information on Ingredients
Product Name & Other Names: Aluminum Chlorohydrate Powder or Aluminium Chlorohydrate Powder or Poly Aluminium Chloride.
CAS No.: 1327-41-9
EINECS: EC Number: 215-477-2
4. First Aid Measures
Always seek medical attention after first aid measures are provided.
Inhalation: Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical attention.
Ingestion: Never give anything by mouth to an unconscious person. Get medical attention.
Skin Contact: Wipe off excess material from skin then immediately flush skin with plenty of water for at least 15 minutes. Remove contaminated clothing and shoes. Get medical attention. Wash clothing before reuse. Thoroughly clean shoes before reuse.
Eye Contact: Immediately flush eyes with plenty of water for at least 15 minutes, lifting lower and upper eyelids occasionally. Get medical attention immediately.
Note to Physician: Treat symptomatically.
5. Fire Fighting Measures
Flammability of the Product: The product is not flammable.
Products of Combustion: It forms oxides of aluminum and hydrochloric acid when heated to decomposition.
Fire Extinguishing Media: Use water spray, dry chemical, foam, or carbon dioxide.
Special Information In the event of a fire, wear full protective clothing and NIOSH-approved self-contained breathing apparatus with full face piece operated in the pressure demand or other positive pressure mode. At high temperatures or when moistened under fire conditions, it may produce toxic or irritating fumes.
6. Accidental Release Measures
Personal precautions, protective equipment and emergency procedures: Avoid breathing dust/fumes/gas/mist/vapors/spray. Use individual protective equipment (waterproof boots, suitable protective clothing, safety glasses, etc). Do not approach facing the wind.
Environmental precautions: Do not let the product enter drains, soil or water sources.
Methods and materials used for containment Cleanup procedures and Storage: Contain spilled material. Do not let the product enter drains. Use a shovel to put the material into a convenient waste disposal container. Finish cleaning by spreading water and swab.
7. Handling and Storage
Precautions for safe handling: Apply according to good manufacturing and industrial hygiene practices. Ensure proper ventilation. In case of insufficient ventilation, wear suitable respiratory equipment. Wash thoroughly after handling. Do not drink, eat or smoke while handling. Avoid contact with skin, eyes and clothing. Minimize dust generation. Avoid breathing dust/fumes/gas/mist/vapors/spray. Avoid contact with eyes, skin, and clothing. Keep container tightly closed. Avoid ingestion and inhalation. Use individual protective equipment (waterproof boots, suitable protective clothing, safety glasses, etc). Prevent any contact with hot surfaces.
Conditions for safe storage, including any incompatibilities: Store in cool, dry and ventilated area away from heat sources and protected from sunlight in tightly closed original container. Keep air contact to a minimum. Do not leave the material container open. Store protected from heat, sparks and ignition sources and incompatible materials. Avoid inhalation of dust/mist/vapor. Do not store with incompatible materials like oxidizing material, acids, alkalis and combustible substances. It is to be stored in corrosive area.
8. Exposure Controls/Personal Protection
Airborne Exposure Limits: None established. Assure it as below 2mg/m3.
Ventilation System: A system of local and/or general exhaust is recommended to keep employee exposures as low as possible.
Personal Respirators (NIOSH Approved): For conditions of use where exposure to dust or mist is apparent and engineering controls are not feasible, a particulate respirator may be worn.
Skin Protection: Wear protective gloves and clean body-covering clothing.
Eye Protection: Use chemical safety goggles and/or full face shield where dusting or splashing of solutions is possible. Maintain eye wash fountain and quick-drench facilities in work area.
Other Control Measures: Maintain good housekeeping in work area. Handle in accordance with good industrial hygiene and safety practice.
9. Physical and Chemical Properties
Appearance: White to yellowish Powder.
Odor: None
Odor threshold: Not available.
pH: Not available.
Relative density: 1.7
Melting Point: Not available.
Initial boiling point and boiling range: Not available.
Flash point: Not available.
Auto-ignition temperature: Not available.
Decomposition temperature: Not available.
Upper/lower flammability or explosive limits: Not available.
Vapor pressure: Not available.
Vapor density: Not available.
Evaporation rate: Not available.
Flammability (solid, gas): Not available.
Partition coefficient: n-octanol/water: Not available.
Solubility: Readily soluble in water.
Viscosity: Not available.
10. Stability and Reactivity
Stability: Stable under ordinary conditions of use and storage. It must be kept in airtight containers.
Hazardous Decomposition Products: It produces oxides of aluminum along with hydrochloric acid when heated to decomposition.
Hazardous Polymerization: Will not occur.
Incompatibilities: Incompatible with oxidizing material acids and alkalis.
Conditions to Avoid: Heat, Sun light, Incompatibles, Metals.
11. Toxicological Information
Routes of Entry: Inhalation, Ingestion, Contact.
Toxicity to Animals: Oral, rat: LD50 = 9187 mg/kg.
Carcinogenic Effects: Not a reported carcinogen.
Mutagenic Effects: Not available.
Teratogenic Effects: Not available.
Developmental Toxicity: Not available.
12. Ecological Information
Environmental Toxicity: Toxicity to fish: LC50 - fish - Not available
BOD5 and COD: Not available.
Persistence and Degradability: No information available.
Mobility: No information available.
Bioaccumulation/ Accumulation: No information available.
Results of PBT and vPvB assessment: No data available for assessment.
Avoid draining the material in waterways.
13. Disposal Considerations
Whatever cannot be saved for recovery or recycling should be managed in an appropriate and approved waste disposal facility. Processing use or contamination of this product may change the waste management options.
14. Transport Information
DOT (USA) & ADR/RID: Not Regulated.
IMDG: Not Regulated.
IATA: Not Regulated.
15. Regulatory Information
USA:
SARA 311/312 Hazards: As per section 2. Immediate Acute Health Hazard.
California Prop 65: This product does not contain any chemicals known to State of California to cause cancer, birth defects, or any other reproductive harm.
16. Other Information
Disclaimer:
**************************
Our company provides this MSDS sheet in good faith but makes no representation as to its comprehensiveness or accuracy. This SDS sheet is intended only as a guide to the appropriate precautionary handling of the material by a properly trained person using this product. The above information has been compiled from various sources and has the possibility of discrepancy and being out-dated information. Individuals receiving the information must exercise their independent judgment and do further search in determining its appropriateness for a particular purpose. In no case shall our company be liable to loss or damages by the product user.
**************************
Anmol Chemicals & Pharmaceuticals Pvt. Ltd. is an off-shoot of Anmol Chemicals Taloja. It is located in MIDC Taloja and it is manufacturing pharmaceutical grades of API, Excepients, Food grade and Reagent grade chemicals. Anmol Chemicals & Pharmaceuticals Pvt. Ltd. is a several decades old group of companies, engaged in manufacturing, supplying, distributing, wholesale supplies for actual users, retail or small pack supplies for research and development chemicals, fine and speciality chemicals, pharmaceutical excipients, mineral fortifiers in chemically pure, Analytical reagent grade, IP BP USP Ph Eur EP JP and other pharmaceutical grade monograph including FCC Food grade chemicals and Nutraceuticals, Mineral Fortifiers at best prices.
Aluminum Chlorohydrate Structure
Aluminium Chlorohydrate CAS Number 12042-91-0, Aluminum Chlorohydrate Solution Dihydrate and CAS Number Dihydrate 1327-41-9 Aluminum Chlorohydrate Anhydrous Manufacturer Exporter
ANMOL CHEMICALS & PHARMACEUTICALS Pvt. Ltd.
India, USA, Europe, UAE
TELEPHONE: +912223770100
Navi Mumbai, INDIA
e-mail: info(At the rate i.e. @)anmol.org
Copyright. 23-nov-24
We manufacture:
Glacial Acetic Acid Manufacturer
Aluminum Chloride Hexahydrate Anhydrous
Aluminum Chlorohydrate Solution Powder
Aluminium Sodium Silicate or Sodium Aluminosilicate
Dihydroxyaluminum Aminoacetate
Dihydroxyaluminum Sodium Carbonate
Chlorhexidine Hydrochloride or Chlorhexidine Dihydrochloride or Chlorhexidine