CAS Number 72-17-3, Sodium Lactate USP BP Ph Eur FCC Food Grade Manufacturers Exporters

Home ------ Contact Anmol Chemicals Industries

Chemical Exporter Air Cargo JarPacked Chemicals Pail for Chemicals Carboys Jumbo packing

Sodium Lactate Manufacturers Exporters
CAS Number 72-17-3, Sodium Lactate Manufacturer Exporter

For Properties Specifications of Sodium Lactate Click Properties, Specifications of Sodium Lactate Manufacturer.

For Uses of Sodium Lactate Click Uses of Sodium Lactate Manufacturer.

For For SDS MSDS Sheet of Sodium Lactate Click SDS Safety Data Sheet MSDS Sheet of Sodium Lactate Manufacturer.

The Properties and Specifications of Sodium Lactate:

Sodium Lactate Solution USP Grade Specifications
Sodium Lactate Solution is an aqueous solution containing not less than 50.0 percent, by weight, of monosodium lactate. It contains not less than 98.0 percent and not more than 102.0 percent of the labeled amount of C3H5NaO3.
Label it to indicate its content of sodium lactate.

Identification: It responds to the tests for Sodium and for Lactate.
pH: between 5.0 and 9.0.
Chloride: A portion, equivalent to 1 g of sodium lactate, shows no more chloride than corresponds to 0.7 mL of 0.020 N hydrochloric acid (0.05%).
Sulfate: To 10 mL of a solution (1 in 100) add 2 drops of hydrochloric acid and 1 mL of barium chloride TS: no turbidity is produced.
Heavy metals: Dilute a quantity of Solution, equivalent to 2.0 g of sodium lactate, with 1 N acetic acid to 25 mL: the limit is 0.001%.
Sugars: To 10 mL of hot alkaline cupric tartrate TS add 5 drops of Solution: no red precipitate is formed.
Limit of citrate, oxalate, phosphate, or tartrate: Dilute 5 mL with recently boiled and cooled water to 50 mL. To 4 mL of this solution add 6 N ammonium hydroxide or 3 N hydrochloric acid, if necessary, to bring the pH to between 7.3 and 7.7. Add 1 mL of calcium chloride TS, and heat in a boiling water bath for 5 minutes: the solution remains clear.
Limit of methanol and methyl esters
:
Potassium permanganate and phosphoric acid solution— Dissolve 3 g of potassium permanganate in a mixture of 15 mL of phosphoric acid and 70 mL of water. Dilute with water to 100 mL.
Oxalic acid and sulfuric acid solution: Cautiously add 50 mL of sulfuric acid to 50 mL of water, mix, cool, add 5 g of oxalic acid, and mix to dissolve.
Standard preparation: Prepare a solution containing 10.0 mg of methanol in 100 mL of dilute alcohol (1 in 10).
Test preparation: Place 40.0 g in a glass-stoppered, round-bottom flask, add 10 mL of water, and add cautiously 30 mL of 5 N potassium hydroxide. Connect a condenser to the flask, and steam-distill, collecting the distillate in a suitable 100-mL graduated vessel containing 10 mL of alcohol. Continue the distillation until the volume in the receiver reaches approximately 95 mL, and dilute the distillate with water to 100.0 mL.
Procedure: Transfer 10.0 mL each of the Standard preparation and the Test preparation to 25-mL volumetric flasks, to each add 5.0 mL of Potassium permanganate and phosphoric acid solution, and mix. After 15 minutes, to each add 2.0 mL of Oxalic acid and sulfuric acid solution, stir with a glass rod until the solution is colorless, add 5.0 mL of fuchsin-sulfurous acid TS, and dilute with water to volume. After 2 hours, concomitantly determine the absorbances of both solutions in 1-cm cells at the wavelength of maximum absorbance at about 575 nm, with a suitable spectrophotometer, using water as the blank: the absorbance of the solution from the Test preparation is not greater than that from the Standard preparation (0.025%).


Sodium Lactate BP Grade Ph Eur Specifications

DEFINITION
Solution of a mixture of the enantiomers of sodium 2-hydroxypropanoate in approximately equal proportions.

Content: Minimum 50.0 per cent m/m of sodium 2-hydroxypropanoate (C3H5NaO3); 96.0 per cent to 104.0 per cent of the content of sodium lactate stated on the label.

CHARACTERS
Appearance: Clear, colourless, slightly syrupy liquid.
Solubility: Miscible with water and with alcohol.

IDENTIFICATION
A. To 0.1 ml add 10 ml of water. 5 ml of the solution gives the reaction of lactates.
B. It gives reaction of sodium.

TESTS
Solution S: Dilute a quantity of the substance to be examined corresponding to 40.0 g of sodium lactate to 200 ml with distilled water.
Appearance of solution: The substance to be examined is clear and not more intensely coloured than reference solution.
pH: 6.5 to 9.0 for the substance to be examined.
Reducing sugars and sucrose: To 5 ml of the substance to be examined add 2 ml of dilute sodium hydroxide solution and 0.2 ml of copper sulphate solution. The solution is clear and blue and remains so on boiling. Add to the hot solution 4 ml of hydrochloric acid. Boil for 1 min. Add 6 ml of strong sodium hydroxide solution and heat to boiling again. The solution is clear and blue.
Methanol: the limit is 50 ppm calculated with reference to sodium lactate, if intended for use in the manufacture of parenteral dosage forms, dialysis, haemodialysis or haemofiltration solutions.
Chlorides: Maximum 50 ppm calculated with reference to sodium lactate.
Oxalates and phosphates: To pass the test.
Sulphates: Maximum 100 ppm calculated with reference to sodium lactate.
Aluminium: Maximum 0.1 ppm, if intended for use in the manufacture of parenteral dosage forms, dialysis, haemodialysis or haemofiltration solutions.
Atomic absorption spectrometry: To pass the test.
Barium: To 10 ml of solution S add 10 ml of calcium sulphate solution. Allow to stand for 30 min. Any opalescence in the solution is not more intense than that of a standard prepared at the same time and in the same manner using a mixture of 10 ml of solution S and 10 ml of distilled water R.
Iron: Maximum 10 ppm calculated with reference to sodium lactate.
Heavy metals: Maximum 10 ppm calculated with reference to sodium lactate.
Bacterial endotoxins: Less than 5 IU/g, if intended for use in the manufacture of parenteral dosage forms without a further appropriate procedure for the removal of bacterial endotoxins.


Sodium Lactate Solution FCC Food Grade Specifications
2-Hydroxypropanoic Acid, Monosodium Salt
C3H5NaO3 Formula weight, anhydrous 112.06
CAS 72-17-3

DESCRIPTION
Sodium Lactate Solution occurs as a clear, colorless or practically colorless, slightly viscous liquid that is odorless or has a slight, not unpleasant odor. It is miscible with water. It is normally available in solutions with concentrations ranging from 60% to about 80%, by weight.

Function: Emulsifier; flavor enhancer; flavoring agent or adjuvant; humectant; pH control agent.

REQUIREMENTS
Indicate the content, by weight, of sodium lactate (C3H5NaO3).
Identification: A sample gives positive tests for Sodium and for Lactate.
Assay: Not less than 50.0%, by weight, and not less than 98.0% and not more than 102.0%, by weight, of the labeled amount of C3H5NaO3.
Chloride: Not more than 0.05%.
Citrate, Oxalate, Phosphate, or Tartrate: Passes test.
Cyanide: Not more than 0.5 mg/kg.
Lead: Not more than 2 mg/kg.
Methanol and Methyl Esters: Not more than 0.025%.
pH: Between 5.0 and 9.0.
Sugars: Passes test.
Sulfate: Not more than 0.005%.


The Uses of Sodium Lactate:
Sodium Lactate is an electrolyte replenisher and systemic alkalizer used as a source of bicarbonate for prevention or control of mild to moderate metabolic acidosis in patients with restricted oral intake whose oxidative processes are not seriously impaired. Sodium Lactate is used in short term fluid replacement after trauma and dehydration. It has a role as a food preservative and a food acidity regulator.


The MSDS-SDS Hazard Statement of Sodium Lactate:

Sodium Lactate SDS, Safety Data Sheet
MSDS Sheet, Material Safety Data Sheet
 25-Jan-23

Section 1: Chemical Product Identification

Product Name: Sodium Lactate or Sodium DL-lactate or Lactic acid sodium salt.
CAS#: 72-17-3
EINECS EC Number: 200-772-0
Molecular Weight
: 112.06
Chemical Formula: C3H5NaO3
Recommended usage: Industrial Manufacturing.

Section 2: Hazards Identification

GHS, Globally Harmonized System Classification in accordance with 29 CFR 1910
Classification according to Regulation (EC) No 1272/2008

Not a hazardous substance or mixture according to Regulation (EC) No. 1272/2008.
This substance is not classified as dangerous according to Directive 67/548/EEC.

Labeling according to GHS & Regulation (EC) No 1272/2008

GHS Label Elements
None

Signal Words: None

Precautionary statements:
P261: Avoid breathing dust/fume/gas/mist/vapors/spray.
P262: Do not get in eyes, on skin, or on clothing.
P281: Use personal protective equipment as required.
P302+P352: IF ON SKIN: Wash with plenty of soap and water.
P304+P340: IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.
P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.

Section 3: Composition and Information on Ingredients

Product Name: Sodium Lactate or Sodium DL-lactate or Lactic acid sodium salt.
CAS#: 72-17-3
EINECS EC Number: 200-772-0
% by Weight
: 50-70% in water.

Section 4: First Aid Measures

Always get medical attention after the first aid is over.

Eye Contact: Check for and remove any contact lenses. In case of contact, immediately flush eyes with plenty of water for at least 15 minutes. Get medical attention if irritation occurs.
Skin Contact: Wash with soap and water. Cover the irritated skin with an emollient. Get medical attention if irritation develops.
Inhalation: If Sodium Lactate is inhaled, remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical attention.
Ingestion: Do Not induce vomiting unless directed to do so by medical personnel. If large quantities of this material are swallowed, call a physician immediately. Loosen tight clothing.

Section 5: Fire and Explosion Data

Flammability of the Product: Not classed as fire hazard but it may be combustible at high temperature.
Products of Combustion: Oxides of sodium and carbon along with fumes .
Fire Fighting Media and Instructions: Use DRY chemical powder, water spray, carbon dioxide, fog or foam. Do not use water jet.
Special Information: In the event of a fire, wear full protective clothing and NIOSH-approved self-contained breathing apparatus with full face piece operated in the pressure demand or other positive pressure mode. At high temperatures under fire conditions, it may produce toxic or irritating fumes. Fire-extinguishing work is done from the windward and the suitable fire-extinguishing method according to the surrounding situation is used.

Section 6: Accidental Release Measures

Personal precautions, protective equipment, and emergency procedures: Avoid breathing dust/fumes/gas/mist/vapors/spray. Use individual protective equipment (waterproof boots, suitable protective clothing, safety glasses, etc.). Do not approach facing the wind.
Environmental precautions: Do not let the product enter drains, soil, or water sources.
Methods and materials used for containment Cleanup procedures and Storage: Large Spill: Do not inhale vapors, mist, or gas. Avoid dust formation. Contain spilled material. Cover with an inert, non-combustible absorbent material, (e.g. sand, earth, diatomaceous earth, vermiculite). Use a shovel to put the material into a convenient waste disposal container.

Section 7: Handling and Storage

Precautions for safe handling: Apply according to good manufacturing and industrial hygiene practices. Ensure proper ventilation. In case of insufficient ventilation, wear suitable respiratory equipment. Wash thoroughly after handling. Do not drink, eat, or smoke while handling. Avoid contact with skin, eyes, and clothing. Minimize dust generation. Avoid breathing dust/fumes/gas/mist/vapors/spray. Keep container tightly closed. Avoid ingestion and inhalation. Use individual protective equipment (waterproof boots, suitable protective clothing, safety glasses, etc.).
Conditions for safe storage, including any incompatibilities: Store in cool, dry, and ventilated area away from heat sources and protected from sunlight in tightly closed original container. Keep air contact to a minimum. Store protected from heat, sparks and ignition sources and incompatible materials. Avoid contact with skin and eyes. Avoid inhalation of dust/mist/vapor. Do not store with incompatible materials like strong oxidizing agents. Ground all equipment containing material. Avoid heat and light.

Section 8: Exposure Controls/Personal Protection

Exposure Limits: This product does not contain any hazardous materials with occupational exposure limits established by the region-specific regulatory bodies.
Engineering Controls: Use process enclosures, local exhaust ventilation, or other engineering controls to keep airborne levels below recommended exposure limits.
Ventilation System: A system of local and/or general exhaust is recommended to keep employee exposures as low as possible.
Personal Respirators (NIOSH Approved): For conditions of use where exposure to dust or mist is apparent and engineering controls are not feasible, a particulate respirator may be worn.
Skin Protection: Wear protective gloves and clean body-covering clothing.
Eye Protection: Use chemical safety goggles and/or full face shield where dusting or splashing of solutions is possible. Maintain eye wash fountain and quick-drench facilities in work area.
Other Control Measures: Maintain good housekeeping in work area. Handle in accordance with good industrial hygiene and safety practice.

Section 9: Physical and Chemical Properties

Physical state and appearance: Solid (Off-white powder). The solution is liquid.
Odor: Odorless.
Odor threshold: Not available.
pH (1% soln/water): Neutral.
Relative density: Not available.
Melting point/freezing point: Not available.
Initial boiling point and boiling range: Not available.
Flash point: Not available.
Auto-ignition temperature: Not available.
Decomposition temperature: Not available.
Upper/lower flammability or explosive limits: Not available.
Vapor pressure: Not available.
Vapor density: Not available.
Evaporation rate: Not available.
Flammability (solid, gas): Not available.
Partition coefficient: n-octanol/water: Not available.
Solubility: Soluble in cold water, hot water.
Viscosity: Not available.

Section 10: Stability and Reactivity Data

Stability: Stable.
Incompatibility with various substances: Oxidizing agents light and heat.
Hazardous Decomposition Products: May form carbon dioxide and carbon monoxide, various hydrocarbons fumes and oxide of sodium.
Corrosivity: Not available.
Polymerization: Will not occur.

Section 11: Toxicological Information

Toxicity to Animals:
LS50/intraperitoneal/rat = 2000 mg/kg
LD50/oral/rat = 2000 mg/kg.
Carcinogenicity: No component of this product present at levels greater than or equal to 0.1% is identified as possible or confirmed human carcinogen by IARC, ACGIH, OSHA and NTP.
Mutagenic Effects: Not available.
Developmental Toxicity: Not available.
Reproductive Effects: No information available.

Section 12: Ecological Information

Toxicity to fish: No information available.
Persistence and Degradability: Easily degradable.
Mobility: Likely to be mobile due to water solubility.
Bioaccumulation/ Accumulation: No information available.
Results of PBT and vPvB assessment: No data available for assessment.

Section 13: Disposal Considerations

Waste Disposal: To be disposed as per legal requirement.

Section 14: Transport Information

DOT USA, TDG Canada & ADR/RID Europe: controlled.
IMDG/IMO: Not controlled.
IATA/ICAO: Not controlled.

Section 15: Other Regulatory Information

USA Federal and State Regulations:
SARA 311/312 Hazards: See section 2.

Section 16: Other Information

DISCLAIMER: The information and recommendations set forth herein are presented in good faith and believed correct as of the date hereof. It is compiled from various sources and it is not necessarily all inclusive nor fully adequate in every circumstance. In addition, these suggestions should not be confused with nor followed in violation of applicable laws, regulations, rules or insurance requirements applicable. This MSDS sheet is intended only as a guide to the appropriate precautionary handling of the material by a properly trained person using this product. Individuals receiving the information must exercise their independent judgment in determining its appropriateness for a particular purpose.

Anmol Chemicals & Pharmaceuticals Pvt. Ltd. is an off-shoot of Anmol Chemicals Taloja. It is located in MIDC Taloja and it is manufacturing pharmaceutical grades of API, Excepients, Food grade and Reagent grade chemicals. Anmol Chemicals & Pharmaceuticals Pvt. Ltd. is a several decades old group of companies, engaged in manufacturing, supplying, distributing, wholesale supplies for actual users, retail or small pack supplies for research and development chemicals, fine and speciality chemicals, pharmaceutical excipients, mineral fortifiers in chemically pure, Analytical reagent grade, IP BP USP Ph Eur EP JP and other pharmaceutical grade monograph including FCC Food grade chemicals and Nutraceuticals, Mineral Fortifiers at best prices.

Sodium Lactate Suppliers
Sodium Lactate Structure

CAS Number 72-17-3, Sodium Lactate Manufacturer Exporter

ANMOL CHEMICALS & PHARMACEUTICALS Pvt. Ltd.
India, USA, Europe, UAE
TELEPHONE: +912223770100
Navi Mumbai, INDIA

e-mail: info(At the rate i.e. @)anmol.org

Copyright. 25-nov-24

We manufacture:

Glacial Acetic Acid Manufacturer

Ammonium Persulfate Exporter

Boric Acid

Calcium Fructoborate

Calcium Glycerophosphate

Calcium Lactate

Calcium Lactate Gluconate

Calcium Lactobionate

Calcium Magnesium Lactate Gluconate

Calcium Saccharate Supplier

Carbamide Peroxide

Chromic Chloride

Gluconolactone

Glucuronolactone

Lactic Acid

Lactobionic Acid

Lithium Carbonate

Magnesium Lactate

Medium-Chain Triglycerides or Caprylic Capric Triglyceride

Nebivolol Hydrochloride or Nebivolol HCl

Octyldodecanol

Oleic Acid

Propionic Acid

Propylene Carbonate

Selenious Acid

Sodium Bromate

Sodium Diacetate

Sodium Erythorbate

Sodium Formate

Sodium Gluconate

Hydrated Sodium Glycerophosphate

Sodium Hydroxide

Sodium Hyaluronate

Sodium Lactate

Sodium Lactobionate

Sodium Metabisulfite

Sodium Methylparaben

Sodium Molybdate Dihydrate

Sodium Selenite

Vanadyl Sulfate